Di Posting Oleh : Simple Learning
Kategori : Multicast
Prerequisites: CCNP level skills.
Personal Note!
Finding things out is a real pleasure ... Time to continue to get the buzz before all these memories drown in oblivion ...
Topology
Pic. 1 - Topology Diagram.
Note!
Routers and switches are already configured as per the topology diagram. All devices use OSPF area 0 as their routing protocol.
Routers and switches are already configured as per the topology diagram. All devices use OSPF area 0 as their routing protocol.
Task 1
Enable PIM Sparse mode on the following interfaces:
Configure R2 to be BSR and R5 to be RP. Use the most stable interface on R2 and R5 to accomplish the task.
Task 3
Use R4 to simulate multicast server sending packets to 224.46.46.46. Users on VLAN 26 should receive this multicast feed. Verify your solution.
- R1 - Fa0/0
- R1 - S0/0.125
- R2 - Fa0/0
- R2 - Fa0/1
- R2 - S0/0
- R4 - Fa0/0
- R5 - Fa0/0
- R5 - S0/0
Configure R2 to be BSR and R5 to be RP. Use the most stable interface on R2 and R5 to accomplish the task.
Task 3
Use R4 to simulate multicast server sending packets to 224.46.46.46. Users on VLAN 26 should receive this multicast feed. Verify your solution.
Solution
R1 Configuration:
R2 Configuration:
R4 Configuration:
R5 Configuration:
Verification:
Task 2
R2 Configuration:
R5 Configuration:
Verification:
Task 3
R6 Configuration:
Verification:
Note!
R5 is the RP for all multicast groups. In the output the RPF nbr 0.0.0.0 implies this fact. The (*,G) entries show up in the client-to-RP path as expected).
Task 1
Enable PIM Sparse mode on the following interfaces:
- R1 - Fa0/0
- R1 - S0/0.125
- R2 - Fa0/0
- R2 - Fa0/1
- R2 - S0/0
- R4 - Fa0/0
- R5 - Fa0/0
- R5 - S0/0
R1 Configuration:
!
ip multicast-routing
!
interface FastEthernet0/0
ip address 10.1.14.1 255.255.255.0
ip pim sparse-mode
speed 100
full-duplex
ip address 10.1.14.1 255.255.255.0
ip pim sparse-mode
speed 100
full-duplex
!
interface Serial0/0.125 multipoint
ip address 10.1.125.1 255.255.255.0
ip pim sparse-mode
ip ospf network point-to-multipoint
snmp trap link-status
frame-relay map ip 10.1.125.2 102 broadcast
frame-relay map ip 10.1.125.5 105 broadcast
frame-relay map ip 10.1.125.1 102
!
ip address 10.1.125.1 255.255.255.0
ip pim sparse-mode
ip ospf network point-to-multipoint
snmp trap link-status
frame-relay map ip 10.1.125.2 102 broadcast
frame-relay map ip 10.1.125.5 105 broadcast
frame-relay map ip 10.1.125.1 102
!
R2 Configuration:
!
ip multicast-routing
!
interface FastEthernet0/0
ip address 10.1.25.2 255.255.255.0
ip pim sparse-mode
speed 100
full-duplex
!
ip address 10.1.25.2 255.255.255.0
ip pim sparse-mode
speed 100
full-duplex
!
interface FastEthernet0/1
ip address 10.1.26.2 255.255.255.0
ip pim sparse-mode
speed 100
full-duplex
!
ip address 10.1.26.2 255.255.255.0
ip pim sparse-mode
speed 100
full-duplex
!
interface Serial0/0
ip address 10.1.125.2 255.255.255.0
ip pim sparse-mode
encapsulation frame-relay
ip ospf network point-to-multipoint
clock rate 2000000
frame-relay map ip 10.1.125.2 201
frame-relay map ip 10.1.125.1 201 broadcast
frame-relay map ip 10.1.125.5 201
no frame-relay inverse-arp
!
ip address 10.1.125.2 255.255.255.0
ip pim sparse-mode
encapsulation frame-relay
ip ospf network point-to-multipoint
clock rate 2000000
frame-relay map ip 10.1.125.2 201
frame-relay map ip 10.1.125.1 201 broadcast
frame-relay map ip 10.1.125.5 201
no frame-relay inverse-arp
!
R4 Configuration:
!
ip multicast-routing
!
interface FastEthernet0/0
ip address 10.1.14.4 255.255.255.0
ip pim sparse-mode
speed 100
full-duplex
!
ip address 10.1.14.4 255.255.255.0
ip pim sparse-mode
speed 100
full-duplex
!
R5 Configuration:
!
ip multicast-routing
!
interface FastEthernet0/0
ip address 10.1.25.5 255.255.255.0
ip pim sparse-mode
speed 100
full-duplex
ip address 10.1.25.5 255.255.255.0
ip pim sparse-mode
speed 100
full-duplex
!
interface Serial0/0
ip address 10.1.125.5 255.255.255.0
ip pim sparse-mode
encapsulation frame-relay
ip ospf network point-to-multipoint
clock rate 2000000
frame-relay map ip 10.1.125.1 501 broadcast
frame-relay map ip 10.1.125.2 501
frame-relay map ip 10.1.125.5 501
!
ip address 10.1.125.5 255.255.255.0
ip pim sparse-mode
encapsulation frame-relay
ip ospf network point-to-multipoint
clock rate 2000000
frame-relay map ip 10.1.125.1 501 broadcast
frame-relay map ip 10.1.125.2 501
frame-relay map ip 10.1.125.5 501
!
Verification:
Pic.2 - PIM Neighbors of R1.
Pic. 3 - PIM Neighbors of R2.
Task 2
Configure R2 to be BSR and R5 to be RP. Use the most stable interface on R2 and R5 to accomplish the task.
R2 Configuration:
!
interface Loopback102
ip address 172.16.102.1 255.255.255.255
ip pim sparse-mode
!
ip address 172.16.102.1 255.255.255.255
ip pim sparse-mode
!
ip pim bsr-candidate Loopback102 0
!
R5 Configuration:
!
interface Loopback105
ip address 172.16.105.1 255.255.255.128
ip pim sparse-mode
!
ip address 172.16.105.1 255.255.255.128
ip pim sparse-mode
!
ip pim rp-candidate Loopback105
!
Verification:
Pic. 4 - RP Information on R4.
Pic. 5 - RP Information on R5.
Note!
The RP candidate uses default priority 0 (Cisco implementation, whereas the standard uses 192, max. 255). RP with the LOWEST priority (0) is preferred.
http://www.cisco.com/en/US/docs/ios/ipmulti/command/reference/imc_04.html#wp1055223
http://www.cisco.com/en/US/docs/ios/ipmulti/command/reference/imc_04.html#wp1055223
In PIMv2, a BSR is the equivalent of Mapping Agent used in Auto-RP. BSR default priority is 0 (0-255). Candidate with the HIGHEST priority is preferred if multiple BSR candidates exist.
BSR does NOT elect the best RP. The group range to RP mapping is only distributed distributed to routers and they choose the best one for a group.
This information is disseminated on a hop-by-hop basis.
Task 3
Use R4 to simulate multicast server sending packets to 224.46.46.46. Users on VLAN 26 should receive this multicast feed. Verify your solution.
R6 Configuration:
!
interface FastEthernet0/0
ip address 10.1.26.6 255.255.255.0
ip igmp join-group 224.46.46.46
speed 100
full-duplex
ip address 10.1.26.6 255.255.255.0
ip igmp join-group 224.46.46.46
speed 100
full-duplex
!
Verification:
Pic. 6 - Mroute Table on R2.
Pic. 7 - Mroute Table on R5.
R5 is the RP for all multicast groups. In the output the RPF nbr 0.0.0.0 implies this fact. The (*,G) entries show up in the client-to-RP path as expected).
Pic. 8 - Ping (server feed) from R4 results.
0 Response to "Lab 157 - PIM Bootstrap Router"
Post a Comment