Lab 164 - IGMP Timers

Lab 164 - IGMP Timers
Di Posting Oleh : Simple Learning
Kategori : Multicast

Prerequisites: CCNP level skills.



Topology

Pic. 1 - Topology Diagram.


Note!
Routers and switches are already configured as per the topology diagram. 

Task 1
On the multicast segment (VLAN 25), there is only one client wishing to receive multicast traffic. Configure R2 and R5 in such a way that they would stop sending multicast traffic immediately upon receiving IGMP Leave message from this client (default 2.5 seconds).

Task 2
Configure the backup querier on VLAN 25 to assume the querier role if it did not hear the query message in 60 seconds (default time is two times the query interval: 120 seconds). Membership query packets should be sent every 15 seconds (default: 60 seconds) by both R2 and R5.


Task 3
R2 and R5 should force their multicast clients to respond to group query with the group report in maximum 5 seconds (default 10 seconds).

Solution


Task 1
On the multicast segment (VLAN 25), there is only one client wishing to receive multicast traffic. Configure R2 and R5 in such a way that they would stop sending multicast traffic immediately upon receiving IGMP Leave message from this client (default 2.5 seconds).

R2 configuration:

!
ip access-list standard ALL_MULTICAST_GROUPS
 permit 224.0.0.0 15.255.255.255
!
interface FastEthernet0/0
 ip address 10.1.25.2 255.255.255.0
 ip pim sparse-mode
 ip igmp immediate-leave group-list ALL_MULTICAST_GROUPS
 speed 100
 full-duplex
!

R5 Configuration:

!
ip access-list standard ALL_MULTICAST_GROUPS
 permit 224.0.0.0 15.255.255.255
!
interface FastEthernet0/0
 ip address 10.1.25.5 255.255.255.0
 ip pim sparse-mode
 ip igmp immediate-leave group-list ALL_MULTICAST_GROUPS
 speed 100
 full-duplex
!



Task 2
Configure the backup querier on VLAN 25 to assume the querier role if it did not hear the query message in 60 seconds (default time is two times the query interval: 120 seconds). Membership query packets should be sent every 15 seconds (default: 60 seconds) by both R2 and R5.


Note!

The querier for multicast is elected based on the lowest IP address on the link (here it has to be R2).



Pic. 2 - DR (designated querier).

R2 configuration:

!
interface FastEthernet0/0
 ip address 10.1.25.2 255.255.255.0
 ip pim sparse-mode
 ip igmp immediate-leave group-list ALL_MULTICAST_GROUPS
 ip igmp query-interval 15
 speed 100
 full-duplex
!

R5 Configuration:

!
interface FastEthernet0/0
 ip address 10.1.25.5 255.255.255.0
 ip pim sparse-mode
 ip igmp query-interval 15
 ip igmp querier-timeout 60
 speed 100
 full-duplex
!



Task 3 
R2 and R5 should force their multicast clients to respond to group query with the group report in maximum 5 seconds (default 10 seconds).

R2 configuration:

!
interface FastEthernet0/0
 ip address 10.1.25.2 255.255.255.0
 ip pim sparse-mode
 ip igmp query-max-response-time 5
 ip igmp immediate-leave group-list ALL_MULTICAST_GROUPS
 ip igmp query-interval 15
 speed 100
 full-duplex
!

R5 Configuration:

!
interface FastEthernet0/0
 ip address 10.1.25.5 255.255.255.0
 ip pim sparse-mode
 ip igmp query-max-response-time 5
 ip igmp query-interval 15
 ip igmp querier-timeout 60
 speed 100
 full-duplex

0 Response to "Lab 164 - IGMP Timers"

Post a Comment