Lab 188 - RIPng Basic Configuration

Lab 188 - RIPng Basic Configuration
Di Posting Oleh : Simple Learning
Kategori : IPv6


Prerequisites: CCNP level skills.

Topology

Pic2. Layer3 Topology Diagram.

Click the picture to enlarge it.

Task 1

Configure IPv6 network addresses as follows:

• R1's FastEthernet0/1 = 2001:0:0:D7::/64
• R2's FastEthernet0/0 = 2001:0:0:1B::/64

Ensure that the host id is created automatically (off of a router's MAC address)

Task 2

Enable RIPng with the identifier 'CCIE' allowing traffic between Vlan 27 and Vlan 215. Ensure that R1 and R2 can ping their respective Vlans using router's host names as well. Assume there is no IPv6 DNS server in the network.

Solution

Lunch break at work and I am playing in the lab. How geeky am I?

Task 1

Configure IPv6 network addresses as follows:

• R1's FastEthernet0/1 = 2001:0:0:D7::/64
• R2's FastEthernet0/0 = 2001:0:0:1B::/64

Ensure that the host id is created automatically (off of a router's MAC address)

R1 Config:
!
interface FastEthernet0/1
 ip address 172.16.215.1 255.255.255.0
 speed 100
 full-duplex
 ipv6 address 2001:0:0:D7::/64 eui-64

!

R2 Config:
!
interface FastEthernet0/0
 ip address 172.16.27.2 255.255.255.0
 speed 100
 full-duplex
 ipv6 address 2001:0:0:1B::/64 eui-64

!

Task 2

Enable RIPng with the identifier 'CCIE' allowing traffic between Vlan 27 and Vlan 215. Ensure that R1 and R2 can ping their respective Vlans using router's host names as well. Assume there is no IPv6 DNS server in the network.

R1 Config:
!
ipv6 unicast-routing
!
ipv6 router rip CCIE
!

interface Serial0/0
 ip address 172.16.123.1 255.255.255.0
 encapsulation frame-relay
 ipv6 address FE80::1 link-local
 ipv6 address 2001:0:0:123::1/64
 ipv6 rip CCIE enable
 clock rate 2000000
 frame-relay map ip 172.16.123.2 102 broadcast
 frame-relay map ipv6 2001:0:0:123::2 102
 frame-relay map ipv6 FE80::2 102 broadcast
 no frame-relay inverse-arp

!

R2 Config:

!
ipv6 unicast-routing
!
ipv6 router rip CCIE
!
interface Serial0/0
 ip address 172.16.123.2 255.255.255.0
 encapsulation frame-relay
 ipv6 address FE80::2 link-local
 ipv6 address 2001:0:0:123::2/64
 ipv6 rip CCIE enable
 clock rate 2000000
 frame-relay map ip 172.16.123.3 203 broadcast
 frame-relay map ip 172.16.123.2 201
 frame-relay map ip 172.16.123.1 201 broadcast
 frame-relay map ipv6 2001:0:0:123::1 201
 frame-relay map ipv6 FE80::1 201 broadcast
 no frame-relay inverse-arp

!

interface FastEthernet0/0

 ip address 172.16.27.2 255.255.255.0

 speed 100

 full-duplex

 ipv6 address 2001:0:0:1B::/64 eui-64

 ipv6 rip CCIE enable

!

Notice!

You don't have to enable RIPng process in the global config mode. You can enable it directly on the interface(es) instead. The global process will start automatically.

In order to ping the routers by their names without DNS service, you must create ip host mappings (hosts). Your IPv6 addresses will be different than mine here:

R2's Fa0/0 IPv6 address = 2001::1B:C001:AFF:FE16:0

R1's Fa0/1 IPv6 address = 2001::D7:C000:AFF:FE16:1

R1 Config:

!

ipv6 host R2 2001::1B:C001:AFF:FE16:0

!

R2 Config:

!

ipv6 host R1 2001::D7:C000:AFF:FE16:1

!

Verification:

#show hosts

Ping works!

Tweet