Di Posting Oleh : Simple Learning
Kategori : IPv6
Prerequisites: CCNP level skills.
Topology
Notice!
In order to proceed to the next lab you must first complete all the previous labs (from lab 188 onwards).
Pic1. Layer3 Topology Diagram.
Configure IPv6 addresses between SW2 and BB2 as follows:
- SW2 (Vlan 208): 2001:0:0:D0::8/64
- BB2 (Fa0/0): 2001:0:0:D0::FE/64
Task 2
In BB2 configure four loopbacks using the following addresses:
In BB2 configure four loopbacks using the following addresses:
- Loopback 0: 2001:2:2:0::1/64
- Loopback 1: 2001:2:2:1::1/64
- Loopback 2: 2001:2:2:2::1/64
- Loopback 3: 2001:2:2:3::1/64
Enable RIPng with the identifier 'CCIE' between SW2 and BB2. Ensure that SW2 advertises only one learned from BB2. All other RIPng devices should be able to reach more specific prefixes advertised by BB2.
Solution
Task 1
Configure IPv6 addresses between SW2 and BB2 as follows:
- SW2 (Vlan 208): 2001:0:0:D0::8/64
- BB2 (Fa0/0): 2001:0:0:D0::FE/64
SW2 Config:
!
ipv6 unicast-routing
!
interface Vlan208
ip address 198.18.100.8 255.255.255.0
ipv6 address 2001:0:0:D0::8/64
Task 2
In BB2 configure four loopbacks using the following addresses:
int Loopback 0
ipv6 address 2001:2:2:0::1/64
!
int Loopback 1
ipv6 address 2001:2:2:1::1/64
!
int Loopback 2
ipv6 address 2001:2:2:2::1/64
!
int Loopback 3
ipv6 address 2001:2:2:3::1/64
!
Task 3
!
ipv6 unicast-routing
!
interface Vlan208
ip address 198.18.100.8 255.255.255.0
ipv6 address 2001:0:0:D0::8/64
!
BB2 Config:
!
ipv6 unicast-routing
!
interface FastEthernet0/0
ip address 198.18.100.254 255.255.255.0
speed 100
full-duplex
ipv6 address 2001:0:0:D0::FE/64
!
Task 2
In BB2 configure four loopbacks using the following addresses:
- Loopback 0: 2001:2:2:0::1/64
- Loopback 1: 2001:2:2:1::1/64
- Loopback 2: 2001:2:2:2::1/64
- Loopback 3: 2001:2:2:3::1/64
BB2 Config:
!int Loopback 0
ipv6 address 2001:2:2:0::1/64
!
int Loopback 1
ipv6 address 2001:2:2:1::1/64
!
int Loopback 2
ipv6 address 2001:2:2:2::1/64
!
int Loopback 3
ipv6 address 2001:2:2:3::1/64
!
Task 3
Enable RIPng with the identifier 'CCIE' between SW2 and BB2. Ensure that SW2 advertises only one learned from BB2. All other RIPng devices should be able to reach more specific prefixes advertised by BB2.
SW2 Config:
!
interface Vlan208
ip address 198.18.100.8 255.255.255.0
ipv6 address 2001:0:0:D0::8/64
ipv6 rip CCIE enable
!
BB2 Config:
!
interface FastEthernet0/0
ip address 198.18.100.254 255.255.255.0
speed 100
full-duplex
ipv6 address 2001:0:0:D0::FE/64
ipv6 rip CCIE enable
ipv6 rip CCIE summary-address 2001:2:2::/62
!
interface Loopback0
no ip address
ipv6 address 2001:2:2::1/64
ipv6 rip CCIE enable
!
interface Loopback1
no ip address
ipv6 address 2001:2:2:1::1/64
ipv6 rip CCIE enable
!
interface Loopback2
no ip address
ipv6 address 2001:2:2:2::1/64
ipv6 rip CCIE enable
!
interface Loopback3
no ip address
ipv6 address 2001:2:2:3::1/64
ipv6 rip CCIE enable
!
Verification:
Pic. 02 - Summary Prefix.
Pic. 03 - Ping Test.
0 Response to "Lab 190 - RIPng Prefix Summarization"
Post a Comment